TRad
Expired Member-
Posts
85 -
Joined
-
Last visited
Never
TRad's Achievements
-
TRad joined the community
-
Ok thanks
- 5 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Thanks beans. Just looking at your picture attached, I may not have connected up correctly? Are both the positive and negative connected to one terminal in this picture? Relay is same type (but modern square equivalent) from local motor spares. Old one was a blue Lucas cylindrical type relay that looks many years old.
- 5 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Hi have fitted reconditioned starter and new 5 pin starter relay to my tr7. Once connected back up, the ignition light was on w/o the key in the ignition. Don't want to start it as its live for some reason? Any ideas? Cheers
- 5 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Ok thanks
- 16 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Hi beans Re your comment about extending the arches in steel like early sprint works cars, was that using arch repair panels to tack onto existing arches? Cheers Adam
- 16 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Thanks
- 9 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Hi I have a tr7 with dolly sprint engine. Looking to upgrade to elec ignition as points have been a problem for one reason and another. Any recommendations? Thanks
- 9 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Ok so the fuel pump is not new, it's the original one - my mistake. I've replaced the needle valves in both the carb float chambers and there doesn't seem to be muck in there. The old needle valves seemed pretty worn. Floats aren't taking on any petrol to weigh them down. The overflow pipe on rear carb is still piddling out petrol though. Anybody have any ideas what else to check? Carbs were all set up and re balanced etc recently.
- 7 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Ok thanks for the advice. It's a standard fuel pump and has been retuned - does that not make any difference?
- 7 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Yes I did.
- 7 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Hi a bit if advice pls. The rear carbs on my sprint engined tr7 have been pushing fuel out of the overflow pipe when running. It's a constant stream, not a drip. The car was running fine and then started to misfire and run really rough and lumpy, eventually stalling at idle. Having taken the float chamber top off there is petrol in the chamber and the float itself seems to move freely and blowing through the pipe on the cap, the valve works when pressing the float up manually. Before I order a new float and valve, does anyone have any idea if it might be something else? Front carb doesn't have a problem. Recently all tuned up and timing sorted by garage.....cheers
- 7 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Ok thanks. Just got the sprint in my tr7 and replacing components etc off old engine some of which are failing!
- 2 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Hi does anyone know if the standard tr7 starter works on the sprint engine? Cheers
- 2 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Troubling and inconvenient....
- 10 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with:
-
Sure. Have uprated suspension all round and lowered rear trailing arms. I find the lowered 200lb springs a little harsh for my taste. Second hand standard road springs I've used have been a good compromise. The new ones I've problems with are brand new standard supposedly but I'm wondering if rimmers got them mixed up?
- 10 replies
-
- Legacy Forum Import
- TR7
-
(and 3 more)
Tagged with: