Chambers

Can anyone give me some advise on wheel nuts for use with Minator alloys (not sure if that makes a difference)

I;ve had a quik look but there seems to be so many sizes and tapers etc.

It's going onto a Spitfire 1500 with standard hubs

Yeah the bush was more than stubborn, the insert came out virtually welded to the bolt. Where as Ive spent time getting all of the bush out I now know I can just remove the outer which should hopefully be easier!

sorry I meant on the existing rubber ones I am removing there is an outer sleeve for me to remove?

I've just received my full poly bush set but realized it doesnt include rear mounting bushes (117578), this isnt a problem as I know I cant get some.  I am a bit curious however, the original rubbers ones, do they have a metal outer tube, I've removed just about all of the old one but haven't noticed an outer tube.  Hopefully someone can help me and let me know

FYI, here is the Rimmer Bros diagram
http://www.rimmerbros.co.uk/Item--i-GRID005729

There should be a clamp around the pipe that goes to the center (link) pipe and also a couple of bolts (one on each side of the exhaust) that go to a rubber hanger.  Undo all of these and the exhaust should come off eventually

You are a gent, thankyou very much

That sounds like exactly what I am looking for, can you post pics of your set-up and also the fixing point at the rear. I know it's a pain taking the board off but it would really help (whistle)

Thanks for the replies guy, do any of you have any pictures of your set ups and also what types so seats you are using and do you have any issues with the soft top catching them?

I know it wont be to everyones taste but my seatbelts are looking a bit raggy and I really fancy fitting a 3 or 4 point race harness in my Spitfire 1500. Does anyone have any experience of this and can you tell me how you mounted it or even better have some pics

Thought that may be the case, thanks I'll get it taken out tonight

I am stripping down the Spit to tidy remove the body tub I have come to the drivers side section of the dash and am a bit stuck on choke cable, how do I remove the knob or is it a case of disconnecting the cable from the carbs and un threading from there?

Thanks for all the tips guys.  How many people will I need to lift the tub off the chasis?

Thanks Alan, I am based in Darlington, not sure where you are?

If anyone has any posts of their tubs rolled over/propped up that would be great

Thanks for all the tips guys.  How many people will I need to lift the tub off the chasis?

Thanks Alan, I am based in Darlington, not sure where you are?

If anyone has any posts of their tubs rolled over/propped up that would be great

I am wanting to get to the underside of my Spitfire 1500, I was thinking about taking off the body tub but was wondering what the best way to turn over the body to get to the underside is.  Also would I need to leave the doors on?

I dont have a rotisserie and dont want to buy expensive frames as I wont use it again I doubt.

Any ideas would be great

thanks

I am wanting to get to the underside of my Spitfire 1500, I was thinking about taking off the body tub but was wondering what the best way to turn over the body to get to the underside is.  Also would I need to leave the doors on?

I dont have a rotisserie and dont want to buy expensive frames as I wont use it again I doubt.

Any ideas would be great

thanks

Ive seen these previously and wondered.  Is it just a case of fitting them, cut the cill, extend it out then just weld the sill back up? I know that sounds very simplistic and you have to check the doors etc but Im just checking this is it in a round about way?

Ive seen these previously and wondered.  Is it just a case of fitting them, cut the cill, extend it out then just weld the sill back up? I know that sounds very simplistic and you have to check the doors etc but Im just checking this is it in a round about way?