davidb5964
Club Member-
Posts
63 -
Joined
-
Last visited
Content Type
Forums
Blogs
Events
Downloads
Gallery
Membership & Shop
Everything posted by davidb5964
-
Been a while since I have been on CT site. Now we just need to get people to use it again😁
-
good idea 😄
-
Probably because I have been given a meter 😄 I'll leave it alone .
-
Engine runs well, set up as per original factory manual, points set to 15 thou. any idea what the dwell angle my be or should I just stick to a feeler gauge ? Thanks.
-
https://www.ebay.co.uk/itm/Triumph-OHV-Herald-948cc-Std-Pistons-1959-61/202651121323?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20160908105057%26meid%3D9b41a0060d244e1e8399631cf9196da1%26pid%3D100675%26rk%3D1%26rkt%3D15%26sd%3D202651121323%26itm%3D202651121323%26pmt%3D0%26noa%3D1%26pg%3D2380057&_trksid=p2380057.c100675.m4236&_trkparms=pageci%3A58be471f-ef14-11e9-a033-74dbd180b048%7Cparentrq%3Ace16407316d0a4eaa9e0f76cffff77b1%7Ciid%3A1
-
4 pistons and rings for 948 on fleabay £80
-
Hiya I removed mine and I used a standard 6 sided socket out of my set. Leave the nut on a couple of threads as you tap the wheel off the shaft or you may end up wearing the steering wheel as it beaks free when you tap it. 1 1/16 " from memory so probably used my 27mm socket as I can't remember digging out my large imperial set. Dave
-
But it is nowhere near as loud as the stupid Harley in the street
-
The 3 rivet {which are actually stop pins} are present on both clutches. The 16 rivets hold the individual 8 segments to the adapter plate, the clutch on the left is a monodisc driven plate with all 8 cushion ramps made out of one piece and is more expensive in tooling but quicker make especially assemble. They still have the same facing rivets that hold the facing to the segments or mono disc and they still have the same 3 stop pins holding the disc adapter and retaining plate together Most of our monodisc tooling is now in the bin as production runs are too short. Most driven plates that were OE by ourselves are either made in Italy or India depending on the part number. Ps the stop pins have 2 roles, one ,to hold the whole assembly together and two, to stop the rotation once the springs reach their design load. I made a couple of plates for my Herald myself before the tooling was shipped out.
-
Probably very unfair. But not sure Halfords would be my first choice for an MOT!
-
Not too sure what the cam mech is . I have many door lock parts so I may have one. PS i'm in Warwickshire Dave
-
yep
- 7 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
hi Jon If you need a large torque wrench i can bring one home monday. Dave
-
Advance/retard adjustment vernier thingy on dizzy
davidb5964 replied to daver clasper's topic in Electrical
On mine turning clockwise it comes to the end, the other way has a c clip on the threaded rod near the end, this stops it. If the c clip is missing as mine was it all falls apart, I learnt that the had way- 4 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
if it has an lc number on it in white paint I may be able to up the finger height for you when it is clamped over the driven plate, ie bolted onto the flywheel assuming the drawings are still in the file if it helps. Dave
- 11 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
Hiya A worn driven plate will make the fingers of the d/spring move upwards towards the gearbox, a worn fulcrum on the cast iron pressure plate sends them the other way, believe me I measure them every day !00 miles me thinks it cannot be worn.I would check that the thrust bearing has little pressure on the fingers in its released condition ensuring the master cylinder is returned condition to its Regs Dave
- 13 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
-
just measured my untouched drivers door for you with no seals in: lock end 0.682" quarter light end 0.849" hope this helps Dave
- 14 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
just measured my untouched drivers door for you with no seals in: lock end 0.682" quarter light end 0.849" hope this helps Dave
- 14 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
That's because you can't see it
- 25 replies
-
- Legacy Forum Import
- 1300
-
(and 3 more)
Tagged with:
-
Hiya. Sponsored Tim but could put in on for you. Dave