James1500
Expired Member-
Posts
105 -
Joined
-
Last visited
Never
Content Type
Forums
Blogs
Events
Downloads
Gallery
Membership & Shop
Everything posted by James1500
-
The quality of new mounting rubbers are terrible and will look like that within a month or two! They usually sag and wedge the engine further down when they start to let go
- 8 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
You'll need to give it a whack to shock it loose preferably with a copper mallet while it's under tension
- 10 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
I would have thought the process was similar to early cars, remove 2 UJ bolts and clamp at lower column and pull wheel/shaft to give enough clearance to swap the joint. Did mine this week and wow what a difference!
- 1 reply
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
Canleys stock the blocks and the extended studs and would post?
- 10 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
I'd repair the tapped plates first by welding nuts to the rear of them and then perhaps elongate the holes in the bulkhead to allow for a little movement, if the hinge pins are worn I'd replace them also as you'll make setting the gaps complicated
- 6 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I'd repair the tapped plates first by welding nuts to the rear of them and then perhaps elongate the holes in the bulkhead to allow for a little movement, if the hinge pins are worn I'd replace them also as you'll make setting the gaps complicated
- 6 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I'd fit relays to be safe, your colum switch will last longer ;)
- 6 replies
-
- Legacy Forum Import
- Herald
-
(and 1 more)
Tagged with:
-
I used the adjustable top wishbone conversion to solve the fouling on mine and save using wheel spacers
- 89 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
With the car in third or fourth with ignition on you should be able to hear the solenoid click when you switch the overdrive on, if not then power isnt getting to the solenoid or the solenoid is faulty, you could try putting a 12v feed straight on the solenoid providing its earthed to rule out the solenoid itself.
- 16 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I'd be tempted to attach the skin to the frame loosely and do the final adjustments on the car, that's the only way you can be sure of final fit
- 4 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
Ive had a nut undo itself and subsequently the whole lot came off leaving me on three wheels, not a fantastic experience so I'd suggest a new shaft!
- 24 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
took me ages to get mine fitting half decent too, you get what you pay for with GRP stuff as long as you know what to expect
- 24 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
On a spit they can be removed though and refitted its just a bit awkward
- 11 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I used a new chassis plate but I had to file it down in order for a nice fit between the chassis rails, make sure the inhibitor switch and mechanism works correctly before you use it to reduce the risk of killing the O/D unit
- 15 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
agree with above, if you can get new plates weld nuts on the back of those, that way you're keeping the same thread/bolt size but adding thread so the chance of them stripping again is greatly reduced
- 11 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
As an RBRR virgin the best bit for me was getting to know Dave's courier through the bends in wales and at one point leading a huge convoy while Dave nodded off (apologies if the pace was on the slow side) overall thought the whole experience was brilliant and very well organised :)
-
24 :)
-
Slimboy's RBRR Entry
James1500 replied to sparky_spit's topic in Round Britain Reliability Run (RBRR)
The entry is serious and the car will be done, will hopefully be painting it this weekend, the back up is my spit but as dave hates it's impracticality I'm pretty sure the herald will rise from the current pile of dust =) -
I agree that a central mount is better but unfortunately removing the tank completely to fit an extra point with reinforcement wasn't an option at the time, will make do for now and consider fitting to the roll bar in future :P
- 16 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
Its only slightly off centre and when the belts are adjusted up hardly noticeable its also at a nice height pulling you down and into the seat, I do have the mx5 seats however so the belt sits nicely either side of the headrest
- 16 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
Three point uses the original mount points, you can get harnesses with a open clasped end for use with eyelets or closed plate types with a hole in for use with bolts, four point would require an extra mounting point to be created
- 16 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I have leds in mine and I'm changing back to normal bulbs, reason being, the hot spots on the lenses point at the ground on mine so in the day they appear very dim and people just don't look for them at night they were great though
- 8 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I cranked mine and bolted it at the top of the valance
- 5 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
If it is the pin you can replace it with the modified version which has a 'head' to stop it falling through
- 15 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with:
-
I have fibreglass ones just not got around to fitting
- 28 replies
-
- Legacy Forum Import
- GT6
-
(and 1 more)
Tagged with: